{"product_id":"unisens-e-mit-1-5mm-silikonkabel-max-55a-sm-modellbau-3108","title":"UniSens-E with 1.5mm² silicone cable, max. 55A, SM-Modellbau # 3108","description":"\u003ch1\u003eUniSens-E with 1.5mm silicone cable, max. 55A SM # 3108\u003c\/h1\u003e\n\n\u003cp\u003eWith improved altitude sensor V2. The small, powerful RC telemetry sensor measures and transmits voltage \/ current \/ power \/ capacity \/ energy \/ brushless RPM \/ altitude \/ vario.\u003c\/p\u003e\n\n\u003cp\u003eThe UniSens-E is a pure telemetry sensor specifically for all electric models. It is so small and lightweight, yet so powerful, that it can be used in almost any model. In line with SM-Modellbau's philosophy of supporting as many systems as possible, the UniSens-E also speaks the language of Jeti Duplex (EX), Multiplex M-Link, Graupner HoTT, Robbe\/Futaba FASSTest and JR DMSS. The UniSens-E automatically recognizes HoTT telemetry systems upon delivery. When used with Jeti, Multiplex, Futaba or JR, the telemetry must be specified in the settings beforehand. To change settings via PC or for firmware updates, a suitable USB interface such as order no. 2550 or an existing USB connection cable such as those from Jeti, Multiplex or Graupner is required. Please refer to the manual for more information.\u003c\/p\u003e\n\n\u003cp\u003eWithout additional sensors, the UniSens-E can measure the entire drive, i.e. voltage, current, capacity and even RPM. A special feature is that a brushless RPM sensor is already permanently installed. To measure the RPM, only a small cable connection to one of the three motor phases needs to be established with the enclosed cable. Since a barometric (air pressure) altitude sensor with high resolution is also integrated, an altimeter and a vario are realized with the UniSens-E. Extensive alarms can also be programmed, which are reported via telemetry via the respective transmitter.\u003c\/p\u003e\n\n\u003cp\u003eThe UniSens-E is available with various connector systems, so that no soldering is usually required. The current measurement range extends symmetrically in both directions. This means that the connector assignment, i.e. whether the battery has a male or female plug on the positive pole, does not matter. The measuring direction is simply set in the setup. All measured values of the UniSens-E can also be viewed live directly via our UniDisplay, and all settings and alarms can be programmed.\u003c\/p\u003e\n\n\u003cp\u003eWhether gliders, aerobatic aircraft, helicopters, HLG or slow flyers, the UniSens-E can be used in almost any area due to its low weight and compact size. Of course, the UniSens-E is not only suitable for model aircraft. It can also be installed in RC boats, RC cars, etc.\u003c\/p\u003e\n\n\u003cp\u003eWith the UniSens-E, you acquire a powerful, universal RC telemetry sensor in all respects, which utilizes the possibilities of modern electronics to be a great help to you as a small helper in dealing with your RC models.\u003c\/p\u003e\n\n\u003cp\u003e\u003cbr\u003e\n\u003cb\u003eAnd this is what the UniSens-E can do:\u003c\/b\u003e\u003c\/p\u003e\n\n\u003cul\u003e\n\t\u003cli\u003ecomplete measurement of electric drives with current, voltage, power, capacity, RPM and altitude measurement\u003c\/li\u003e\n\t\u003cli\u003eintegrated brushless RPM sensor\u003c\/li\u003e\n\t\u003cli\u003efull telemetry support for Jeti Duplex (EX), PowerBox Core, Multiplex M-Link, Graupner HoTT, Futaba FASSTest S.BUS2, JR DMSS, Fr Sky and Spektrum\u003c\/li\u003e\n\t\u003cli\u003ealtitude measurement with automatic zeroing after power-on, barometric vario\u003c\/li\u003e\n\t\u003cli\u003ecurrent measurement range up to 140 A in both directions, voltage up to 60 V (however, the maximum current carrying capacity of the connectors used must not be exceeded!)\u003c\/li\u003e\n\t\u003cli\u003econnection for receiver signal for remote control of certain functions\u003c\/li\u003e\n\t\u003cli\u003edirect connection to GPS logger possible for data recording in a file\u003c\/li\u003e\n\t\u003cli\u003emeasurement of receiver battery voltage\u003c\/li\u003e\n\t\u003cli\u003epower supply via receiver\u003c\/li\u003e\n\t\u003cli\u003ecurrent status indicated by LED\u003c\/li\u003e\n\t\u003cli\u003edirect viewing of live or recorded measurements with our UniDisplay\u003c\/li\u003e\n\t\u003cli\u003eparameter settings possible via PC, UniDisplay and telemetry\u003c\/li\u003e\n\t\u003cli\u003ePC software for settings and updates (SM UniSens-E Tool)\u003c\/li\u003e\n\t\u003cli\u003efree firmware updates via PC with our USB interface (order no. 2550) or with existing USB connection cables such as those from Jeti, Multiplex or Graupner (the firmware file can be found here)\u003c\/li\u003e\n\t\u003cli\u003ecan be used almost anywhere due to its compact size and low weight\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cb\u003ePlease refer to the operating instructions for technical data and the complete range of functions.\u003c\/b\u003e\u003c\/p\u003e\n\n\u003cp\u003e \u003c\/p\u003e\n\n\u003cp\u003e\u003cb\u003eTypical wiring examples of the UniSens-E in the model:\u003c\/b\u003e\u003c\/p\u003e\n\n\u003cp\u003e1. altitude measurement only with altitude sensor already integrated in the UniSens-E, e.g., in F3B \/ F3J gliders\u003c\/p\u003e\n\n\u003cp\u003e2. electric drive measurement\u003c\/p\u003e\n\n\u003cp\u003e\u003cbr\u003e\n\u003cb\u003eTechnical data:\u003c\/b\u003e\u003c\/p\u003e\n\n\u003cul\u003e\n\t\u003cli\u003ecurrent measurement range: 140 A in both directions, i.e. - 140 A to + 140 A\u003c\/li\u003e\n\t\u003cli\u003eThe following load durations are permissible: - 100 A unlimited - 120 A for 1 minute - 140 A for 20 seconds (However, depending on the plug system, the limits of the plugs are significantly lower!) Useful values are with - MPX green (double contact) and XT60 continuous: 50 A \/ 20A\u003c\/li\u003e\n\t\u003cli\u003evoltage measurement range: 0 to 60 V\u003c\/li\u003e\n\t\u003cli\u003ealtitude measurement range: 0 to 8000 m above sea level, automatically zeroed when switched on\u003c\/li\u003e\n\t\u003cli\u003ereceiver voltage measurement: 3.8 V to 10 V\u003c\/li\u003e\n\t\u003cli\u003edata rate: 10 Hz\u003c\/li\u003e\n\t\u003cli\u003epower supply from receiver supply via telemetry connection (from 3.8 V to max. 10 V)\u003c\/li\u003e\n\t\u003cli\u003ecurrent consumption: approx. 25 mA\u003c\/li\u003e\n\t\u003cli\u003eexternal connections: 1 connection for telemetry and power supply 1 phase connection for brushless RPM measurement 1 servo pulse input from receiver COM connection for UniDisplay, GPS logger or PC\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cb\u003eDimensions:\u003c\/b\u003e\u003c\/p\u003e\n\n\u003cul\u003e\n\t\u003cli\u003egreen MPX connector: 26 (38) x 29 x 9 mm\u003c\/li\u003e\n\t\u003cli\u003eyellow XT60 connector: 26 (50) x 29 x 9 mm\u003c\/li\u003e\n\t\u003cli\u003e4 mm gold connector: 26 (55) x 22 x 9 mm 5.5 mm gold connector: 26 (44) x 22 x 11 mm\u003c\/li\u003e\n\t\u003cli\u003e6 mm LMT gold connector: 26 (42) x 22 x 11 mm\u003c\/li\u003e\n\t\u003cli\u003eweight: 10 g - 14 g without cable (depending on plug system), connection cable 4 g\u003c\/li\u003e\n\t\u003cli\u003escope of delivery: UniSens-E with integrated altitude sensor \/ vario connection cable to receiver for telemetry \/ power supply connection cable for brushless RPM measurement detailed colored operating instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e \u003c\/p\u003e","brand":"SM-Modellbau","offers":[{"title":"Default Title","offer_id":53448692498775,"sku":"SM3108","price":54.89,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0935\/8318\/0119\/files\/SM3108_b1_9d137f59-48e5-40fb-a77f-80d6b5e78aac.jpg?v=1780656244","url":"https:\/\/hoelleinshop.com\/en\/products\/unisens-e-mit-1-5mm-silikonkabel-max-55a-sm-modellbau-3108","provider":"hoelleinshop","version":"1.0","type":"link"}