Casting Resin P with Hardener P 25, Working Pack Total 400g, R&G # 1151540

Item description see below hazard warnings!

Possible Hazards - Moulding Resin P

Hazard-determining component for labeling

Bisphenol A epichlorohydrin resins with average MW < 700

Signal word: Warning

Pictograms: 

Safety instructions GHS / H-phrases

H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H411 Toxic to aquatic life with long lasting effects.

Safety instructions GHS / P-phrases

P333 P313 If skin irritation or rash occurs: Get medical advice/attention.
P305 P351 P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.

Special labelling of certain mixtures EUH205 Contains epoxy compounds. May produce an allergic reaction.

Possible Hazards - Hardener P-25 (for Moulding Resin P / 20 min)     

Signal word: Danger

Pictograms:

Safety instructions GHS / H-phrases

H302 Harmful if swallowed.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H412 Harmful to aquatic life with long lasting effects.

Safety instructions GHS / P-phrases

P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P303 P361 P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
P305 P351 P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P310 Immediately call a POISON CENTER/doctor.
P405 Store locked up.
P501 Dispose of contents/container in accordance with local regulations.

Moulding Resin P with Hardener P 25, working pack 400g, R&G # 1151540  

Moulding Resin P:

• Hard-elastic, edge-stable
• Very good grindability and polishability (Shore D-hardness Ø 75)
• Thixotropic (non-sagging)
• Manufactured under vacuum, therefore optimally air bubble-free and homogeneous

Black pigmented epoxy resin for surface coats in mould making. High edge stability, polishable. Moulding Resin P is processed and cured at room temperature. It can be used as a surface coat in conjunction with epoxy resin laminates or with laminating ceramics. In contrast to metal-filled systems, the surfaces are polishable. The surface coat is hard-elastic, not brittle, and has good edge stability.

Consumption: approx. 0.6 kg/m² (Ø 0.5 mm layer thickness)

Hardener P-25:

Hardener for Moulding Resin P with a processing time of 20 minutes.

• Very good chemical resistance (largely styrene resistant)
• Free of nonylphenol and benzyl alcohol

Mixing ratio: 100 : 25 parts by weight resin : hardener
Processing time (125 g batch/23 °C): approx. 20 minutes
Gel time (at 20 °C/1 mm layer thickness): approx. 2 hours
Curing time (at 23 °C): 24 hours

Viscosity (ISO 3219/at 25 °C): 150 -170 mPas
Flash point (DIN-ISO 367): > 100 °C
Amine number (TS 31-97): 825 ± 50 mgKOH/g
Gardner color number (DIN ISO 4630-2): < 8
H*-Equivalent weight (calculated): 44 g/Eq.
Solid content: 100 %

Heat deflection temperature: 70 °C